How to Store WPC Decking Before Installation
WPC decking is designed to handle outdoor conditions, but it still needs sensible protection between delivery and installation. Correct storage helps preserve the boards’ shape, surface finish, colour, and connection system, particularly when materials are left on a building site for several weeks.
In Australia, stored decking may face intense ultraviolet light in Perth, humid air in Brisbane, sudden rain in Sydney, or large temperature changes in Melbourne. A dry, shaded, well-supported storage area reduces the risk of bowing, staining, dirt accumulation, and damage to hidden clips or trim pieces.
Start With A Dry, Level Storage Area
Choose a firm, level surface such as a concrete slab, covered garage floor, or stable paved area. Do not place WPC boards directly on soil, grass, sand, or freshly watered ground. Ground moisture can collect beneath the stack, while uneven support may place continuous stress on long profiles.
If indoor storage is unavailable, use a covered carport, verandah, or temporary site shelter. The area should be protected from direct sun and standing water while still allowing air to circulate. Avoid leaning long boards vertically against a wall, as this can create a permanent curve or put pressure on their edges.
Raise the decking above the floor with straight timber bearers, pallets, or suitable supports. Place supports at regular intervals along the length, including near the ends. For long boards, closer support spacing is safer than relying on two supports at either end.
Keep Boards Protected From Australian Weather
Keep the original wrapping in place when it is clean, dry, and undamaged. If the packaging has collected rainwater, remove or loosen it and allow the boards to dry. A tightly sealed plastic cover can trap condensation, especially during warm days and cool nights, so use a breathable cover or leave ventilation gaps at the sides.
Direct sunlight can heat dark WPC profiles significantly, even when the surrounding air feels comfortable. Uneven exposure may cause one side of a board to expand more than the other. Store all packs in consistent shade, away from reflective metal walls, glass, and locations where afternoon sun reaches the stack.
Do not store boards beside freshly painted surfaces, wet concrete, pool chemicals, fertilisers, solvents, or rusty metal. These substances can mark the capped surface or discolour lighter decking. In coastal areas such as Adelaide, Newcastle, or the Gold Coast, salt-laden air is another reason to keep packs covered and away from open exposure.
Stack Profiles Without Causing Distortion
Keep every pack flat and fully supported. Align the bearers beneath the factory support points where possible, then place additional bearers so no long section hangs unsupported. Do not place heavy bricks, tools, tiles, or other building materials on top of WPC decking.
Avoid mixing loose boards, offcuts, and sealed packs in one unstable pile. Loose profiles can slide or twist, while concentrated weight may dent the edges. Stack boards with their lengths aligned and keep different colours, surface patterns, and batches clearly separated.
| Storage method | Suitability | Main precaution |
|---|---|---|
| Covered concrete floor | Excellent for short or long storage | Keep packs raised and away from wall dampness |
| Shaded pallet storage | Suitable on most building sites | Use straight, evenly spaced bearers |
| Open grass or soil | Poor choice | Avoid ground moisture and uneven settlement |
| Vertical wall storage | Usually unsuitable for long boards | Prevent bowing by keeping profiles flat |
| Airtight plastic wrapping | Suitable only when completely dry | Allow ventilation to prevent condensation |
Check the stack after strong wind, heavy rain, or a site delivery. A shifted pallet or torn cover can expose one end of the boards and create localised swelling or staining. Re-stack carefully rather than dragging individual profiles across rough ground.
Protect Accessories And Record The Order
Clips, screws, joists, fascia boards, trims, and stair components should be stored separately in a dry, enclosed area. Small stainless-steel fixings are easy to lose on an active Australian building site, particularly where several trades share a garage or driveway. Keep hardware in its labelled packaging until the frame is ready.
Before moving packs, photograph labels and note the delivery date, product colour, batch information, and quantity. This record helps match boards during installation and supports a warranty or replacement request if damage is discovered. It is also useful when materials are purchased in stages from a wholesale supplier.
Handle boards with two people when their length makes them difficult to control. Lift rather than drag, and keep the profiles clear of sharp gravel, exposed reo, and concrete edges. If a worker has a health concern or uses prescription medicine, they should follow professional medical advice; general information about propranolol safety should never replace guidance from a qualified clinician.
Prepare For Installation And Long-Term Care
Move the decking from storage to the installation area only when the subframe, tools, fasteners, and drainage details are ready. Leaving boards scattered around a site increases the chance of scratches, mud contamination, and accidental damage from vehicles or other trades. Keep each pack protected until it is needed.
Before installation, inspect every board in good daylight. Look for cracks, deep scratches, unusual bowing, damaged grooves, or colour differences between batches. Minor surface dust can be removed with a soft brush, while mud should be rinsed away with clean water and a mild household detergent approved for the product.
Allow the boards to become familiar with the local conditions before fixing them, especially after transport from a warehouse into a hot outdoor area. Follow the manufacturer’s guidance for expansion gaps, joist spacing, fasteners, and ventilation. In Australia, the project may also need to meet applicable state or territory building requirements and workplace health and safety duties; a licensed installer can check site-specific obligations.
Good storage makes installation more predictable, but it does not remove the need for careful design. Pool surrounds, balconies, raised decks, and bushfire-prone locations may have additional requirements for structure, drainage, slip resistance, or material selection. Keeping the products clean, shaded, supported, and documented from delivery onward gives the WPC decking the best start before it becomes part of the finished outdoor area.